spark-o-matic
Group: Members
Posts: 68
Joined: Jan. 2008 |
 |
Posted: Feb. 01 2008,04:13 |
 |
I found this late last night. Google translator didn't work well.
http://www.linux.or.jp/JF/JFdocs/ISAPnP-HOWTO-7.html
but i got the following:
# Card 3: (serial identifier 08 97 19 38 e6 98 50 6d 50)
# Vendor Id TCM5098, Serial Number 2535012582, checksum 0x08.
# Version 1.0, Vendor version 1.0
# ANSI string -->3Com 3C509B EtherLink III<--
#
# Logical device id TCM5098
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
3 $BKgL\$N%+!<%I$N@bL@$G$9!#(B
(CONFIGURE TCM5098/2535012582 (LD 0
# Compatible device id PNP80f7
# IRQ 3, 5, 7, 9, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
IRQ $B$O(B 3,5,7,9,19,11,12,15 $B$NFb(B $B0l$D$,;H$($^$9!#(B
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x03e0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0210) (CHECK))
I/O $B%]!<%H%"%I%l%9$O(B 16 $B%P%$%HJ,$r(B 0x210 $B$+$i(B 16 $B%P%$%HCV$-$K(B 0x3e0 $B$^$G$NFb!"(B
$B0l$D$,;H$($^$9!#(B
(NAME "TCM5098/2535012582[0]{3Com 3C509B EtherLink III}")
# (ACT Y)
$B@_Dj$rM-8z$K$9$k$H$-$K!"(B# $B$r$O$:$7$^$9!#(B
))
# End tag... Checksum 0x00 (OK)
3 $BKgL\$N%+!<%I$N@_Dj$N=*$o$j$G$9!#(B
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
$B$9$Y$F$N%+!<%I$N@_Dj$N=*$o$j$G$9!#(B
Win98SE shows:
3Com EtherLink III ISA (3C509/3C509b) in ISA mode
i/o range 0300 - 030F
irq 10
shows nothing about DMA
Upgading And Repairing PC's by Scott Mueller Fifth Edition 6th printing 1997 mentions nothing about ISA NIC's using DMA.
i verified conectivity to my Lan and the internet on the 98 machine.
modprobe 3c509 irq=10 io=0x300 nopnp=1
causes
warning: io=0x300 is not part of......
and device not found
is that the correct syntax for io=
(oops, brain fart, just reread only irq in source.but I tryed it w/out after the error anyway and still failed)
I also verified these resources are available. (/proc/* is realy helping) Thanks.
next step is swap the card from the 98 machine to the DSL machine in case that card is in PnP mode.
BTW. Your post here is not the same as in the e-mail. Did you edit?
--------------
The smartest person is not the person who knows the most.
The smartest person is the one who knows which book to look in.
Community knowledge can be the sum of it's knowledge or the sum of it's ignorance
The Definition of a 'Brain Fart':
When something comes out of my brain that Stinks!
|
.
DSL Market ,
Great VPS hosting provided by Tektonic
